Metric to Imperial Calculator

 

Convert between millimetres (mm) and inches (in)

Reset

Common Millimetres to Inches Conversions

Quick reference conversions for common metric component sizes.
Millimetres Inches
1mm 0.039in
2mm 0.079in
3mm 0.118in
5mm 0.197in
6mm 0.236in
8mm 0.315in
10mm 0.394in
12mm 0.472in
20mm 0.787in
25.4mm 1in
50mm 1.969in
100mm 3.937in

Common Inches to Millimetres Conversions

Compare common fractional inch sizes with their decimal and metric equivalents.
Inches Decimal Inches Millimetres
1/8" 0.125in 3.18mm
3/16" 0.186in 4.76mm
1/4" 0.25in 6.35mm
5/16" 0.312in 7.94mm
3/8" 0.375in 9.53mm
1/2" 0.5in 12.70mm
5/8" 0.625in 15.86mm
3/4" 0.75in 19.05mm
7/8" 0.875in 22.23mm
1" 1in 25.40mm

Conversion Does Not Mean Component Compatibility

A similar converted dimension does not necessarily mean two components are interchangeable. This is particularly important with fasteners.

Metric

M6

0.236 in

≠

Imperial

1/4"

0.250 in = 6.35 mm

Fastener compatibility can also depend on:

How to Measure an Unknown Fastener Diameter

If you are trying to identify an existing bolt, screw or threaded component, first measure the outside diameter of the threaded section.

1
Measure the Diameter Use digital calipers and measure across the widest point of the thread.
2
Record the Measurement Record the dimension in the unit shown by your measuring equipment or existing specification.
3
Convert the Measurement Enter the measured dimension into the Metric to Imperial Calculator to compare it with the opposite measurement system.
Comparing the diameter can help indicate whether a component is likely to use a metric or imperial specification, but the complete thread specification should still be checked.

Metric vs Imperial Fasteners

Metric and imperial fasteners use different systems for identifying diameter and thread dimensions.

Metric Imperial
Diameter measured in millimetres Diameter measured in inches
Example: M8 Example: 5/16"
Thread pitch usually measured in mm Thread spacing often stated as TPI
Common across UK and European engineering Common in older UK equipment and US equipment
Use Thread Conversion Calculator

How Does the Metric to Imperial Calculator Work?

Metric and imperial measurements use different units to describe the same physical dimension.

The metric system commonly uses millimetres (mm) for fasteners, components and engineering measurements while imperial measurements are normally expressed in inches (in).

Fixed Conversion

1 in = 25.4 mm

Millimetres to Inches

mm ÷ 25.4

Inches to Millimetres

in × 25.4

Need to Identify a Fastener Size?

If you know the diameter but aren't sure whether the component is metric or imperial, use the calculator above to compare the measurements.

If you're trying to identify a complete fastener specification, our Technical Team can help with product identification, measurements and suitable replacement components.

Get Technical Advice

Related Engineering Tools

Continue your calculation using our other fastener and engineering tools.

Thread Conversion Calculator

Convert between Threads Per Inch (TPI) and metric thread pitch.

Use Calculator
Washer Size Finder

Find suitable washer dimensions based on your bolt or screw size.

Use Calculator
Hole Size Calculator

Calculate recommended pilot hole sizes for hardwood and softwood.

Use Calculator
Torque Calculator

Calculate torque using applied force, lever arm length and angle.

Use Calculator

Metric to Imperial Calculator FAQs

Common questions about converting millimetres, inches and fastener dimensions.

Divide the millimetre measurement by 25.4. For example, 100mm ÷ 25.4 = approximately 3.937 inches.

Multiply the inch measurement by 25.4. For example, 0.25in × 25.4 = 6.35mm.

There are exactly 25.4 millimetres in one inch.

One quarter of an inch is 0.25 inches. Multiplying 0.25 by 25.4 gives 6.35mm.

Half an inch equals 12.7mm.

10mm divided by 25.4 equals approximately 0.394 inches.

Not necessarily. Similar diameters do not guarantee compatibility because thread pitch, thread form and tolerances may differ.

Use digital calipers to measure across the outside of the threaded section of the bolt or screw.

Metric and imperial measurements use different units to describe the same physical dimension.

The metric system commonly uses millimetres (mm) for fasteners, components and engineering measurements, while imperial measurements are normally expressed in inches (in).

One inch is exactly equal to 25.4 millimetres, which provides the fixed conversion factor between the two systems.

To convert millimetres into inches, divide by 25.4. To convert inches into millimetres, multiply by 25.4.

Metric measurements are based on the decimal system and are commonly used throughout engineering and manufacturing.

For smaller components such as fasteners, washers, plugs and inserts, dimensions are usually stated in millimetres (mm).

For example:

M8 Bolt

The M8 refers to a nominal thread diameter of approximately 8mm.

Metric dimensions are widely used throughout UK and European engineering specifications.

Imperial measurements commonly use inches and fractions of an inch.

Typical imperial fastener dimensions include:

1/4"
3/8"
1/2"
5/8"

The same dimensions can also be expressed as decimal inches.

For example:

1/4" = 0.25in
1/2" = 0.50in

These measurements can be converted into millimetres by multiplying the decimal inch measurement by 25.4.