Thread Conversion Calculator

 

Convert between Threads Per Inch (TPI) and Metric Pitch (mm)

Reset

Common TPI to Metric Pitch Conversions

Quick reference values for common imperial thread pitches.
TPI Metric Pitch
8 TPI 3.18mm
10 TPI 2.54mm
12 TPI 2.12mm
16 TPI 1.59mm
18 TPI 1.41mm
20 TPI 1.27mm
24 TPI 1.06mm
28 TPI 0.91mm
32 TPI 0.79mm
40 TPI 0.64mm

Common Metric Pitch to TPI Conversions

Compare common metric thread pitches with their approximate TPI equivalent.
Metric Pitch TPI
0.5mm 50.80 TPI
0.7mm 36.286 TPI
0.8mm 31.75 TPI
1mm 25.40 TPI
1.25mm 20.32 TPI
1.5mm 16.933 TPI
1.75mm 14.514 TPI
2mm 12.70 TPI
2.5mm 10.16 TPI
3mm 8.467 TPI

Pitch Conversion Does Not Mean Thread Compatibility

A similar thread pitch does not necessarily mean two threads are interchangeable.

Thread compatibility also depends on factors including:

For example, an imperial thread may calculate to a metric pitch that is very close to a standard metric size, but this does not mean the two fasteners should be used together.

How to Measure an Unknown Thread

If you are trying to identify an existing bolt, screw or threaded component, measure both the diameter and the thread spacing.

1
Measure the Diameter
↔ Outside Thread Diameter
Use digital calipers to measure across the outside of the thread. For metric threads this will generally relate to the nominal diameter, for example M6, M8 or M10.
2
Measure the Thread Pitch or TPI
Metric Threads Measure the distance between adjacent thread peaks in millimetres.
Imperial Threads Use a thread pitch gauge or count the number of threads across one inch to establish the TPI.
3
Compare the Result
⇄ Pitch to and from TPI
Use the Thread Conversion Calculator to compare the measured pitch with the opposite measurement system.

Metric vs Imperial Threads

Metric and imperial fasteners use different systems for describing thread spacing.

Metric Imperial
Pitch measured in millimetres Threads measured per inches
Example: M10 × 1.5 Example: 3/8" - 16 UNC
Smaller Pitch = Finer Thread Higher TPI = Finer Thread
Uses metric nominal diameters Uses imperial nominal diameters
Use Metric to Imperial Calculator

How Does the Thread Conversion Calculator Work?

Metric and imperial threads describe thread spacing differently.

Metric thread pitch measures the distance from one thread crest to the next in millimetres. For example, an M10 × 1.5 thread has a nominal diameter of 10mm and a pitch of 1.5mm.

Threads Per Inch (TPI) measures how many thread peaks occur over one inch. A higher TPI therefore represents a finer thread while a lower TPI represents a coarser thread.

Conversion Factor: 1 in = 25.4 mm

Related Engineering Tools

Continue your calculation using our other fastener and engineering tools.

Metric to Imperial Calculator

Convert fastener dimensions between millimetres and inches.

Use Calculator
Washer Size Finder

Find suitable washer dimensions based on your bolt or screw size.

Use Calculator
Hole Size Calculator

Calculate recommended pilot hole sizes for hardwood and softwood.

Use Calculator
Torque Calculator

Calculate torque using applied force, lever arm length and angle.

Use Calculator

Thread Conversion FAQs

Common questions about TPI, thread pitch and metric to imperial thread conversion.

Divide 25.4 by the number of Threads Per Inch. For example, 20 TPI gives a metric pitch of 1.27mm because 25.4 ÷ 20 = 1.27.

Divide 25.4 by the metric pitch in millimetres. A 1.5mm pitch therefore equals approximately 16.933 TPI.

There are exactly 25.4 millimetres in one inch. This allows thread spacing expressed as Threads Per Inch to be converted into millimetres.

They describe the same general characteristic — the spacing or frequency of threads — but use different measurement methods. Metric threads normally specify the distance between threads, while imperial threads commonly specify the number of threads occurring within one inch.

No. Matching or similar pitch alone does not confirm compatibility. Diameter, thread form, tolerance and thread standard must also be considered.

A thread pitch gauge provides the most reliable method. Metric pitch can also be estimated by measuring the distance between adjacent thread crests with suitable measuring equipment.

Metric and imperial threads describe thread spacing differently.

Metric thread pitch measures the distance from one thread crest to the next in millimetres. For example, an M10 × 1.5 thread has a nominal diameter of 10mm and a pitch of 1.5mm.

Threads Per Inch (TPI) measures how many thread peaks occur over one inch. A higher TPI therefore represents a finer thread, while a lower TPI represents a coarser thread.

Because one inch equals exactly 25.4mm, thread spacing can be converted between the two systems using 25.4 as the conversion factor.

Thread pitch is the distance between corresponding points on two adjacent threads.

For metric fasteners, thread pitch is normally stated in millimetres.

For example:

M8 × 1.25

M8 = nominal thread diameter
1.25 = distance between adjacent threads in millimetres

A smaller pitch represents a finer thread, while a larger pitch represents a coarser thread for the same nominal diameter.

TPI stands for Threads Per Inch and is commonly used when specifying imperial thread types.

It represents the number of complete threads occurring within one inch of threaded length.

For example:

¼"-20 UNC

means the thread has:

¼" nominal diameter
20 threads per inch
UNC thread form

The TPI can be converted into approximate metric pitch using:

25.4 ÷ 20 = 1.270mm